Re: Php4.0.4 Installation on Win98 for Apache 1.3.19

On Sun, 13 May 2001 22:54:42 +0200, you wrote: I assume you set up an alias (scriptalias probably) in your httpd.conf file. Have you tried running the test.php by using the url: http://localhost/php/test.php Or, if your alias is /php4/, then: http://localhost/php4/test.php If that doesn't work, then I can't really see what you might be doing wrong. If you like, send my your httpd.conf and your php.ini and I'll take a look at them (no guarantees, though). Alan >Hi Alan >Thank you, but i have not yet resolved the problem, even if i reduced it. >So, i follewed what you said to me about doc_root. Furthermore i became >aware of one my mistake: i put inside the file httpd.conf of Apache the row > >Port 3000 > >that is wrong. This is right > >Port 80 > >So Apache works fine. >I did the change inside the file php.ini that is placed into C:\Windows. >So I have: >doc_root=D:\Inetpub\Scripts\Php; > >and Document_root of Apache is: >D:\programs\Apache Groups\Apache >If i call http://localhost/ then i see the home page, >if i call http://localhost/test.php then the brouser goes into >a waiting >state. I read in the low bar: >Connect: host localhost contacted.Waiting for replay. >The file test.php, coming with PHP, i put into >D:\Inetpub\Scripts and also into D:\Inetpub\Scripts\PHP. If i do CTRL+ALT+CANC i >see PHP >in the list of processes PHP so i deduce thai PHPm is running, but the >brouser stays waiting. >Thank you for your kindness, but i still need help for solving this problem. >Thank you in advance. > > >Alan Popow wrote: > >> On Sun, 13 May 2001 02:03:45 +0200, you wrote: >> >> I haven't tried running easywindows installer, so I'm just winging it here >> ignoring whatever the installer might be changing from defaults (though I >> doubt it changes the httpd.conf file defaults). >> >> Remember that apache thinks by default that the document root is at >> ....../apache/htdocs, and if you are using the normal iis setup, then your >> index.html is likely not there. In the httpd.conf file, make sure that the >> document root is pointing to the right place. >> >> Then, assuming you added the appropriate lines to Apache's httpd.conf file, >> open up your php.ini and make sure that the doc_root path points to where >> your scripts are. >> >> ie: doc_root = "d:\inetpub\scripts\php" (if that's where they are - in other >> words, where is test.php located). >> >> Alan >> >> >Hello everyone >> >I am trying to install PHP4 with Apache 1.3.19 following the procedure >> >that I see >> > in http://php.weblogs.com/easywindows using the >> > PHP4.0.4easywindows Installer. There is also a mistake, >> > "C:/inetpub/scripts/php/" is wrong, "D:/inetpub/scripts/php/" is >> > right >> >. >> >However, when I run Apache and call http://localhost/ i >> >don't see the >> >home page index.html, >> >furthermore if I call test.php with >> >http://localhost/test.php >> >i don't see any page. In both cases I have a file not found messagge. >> >Can someone explain this behavior. I would like to use PHP with >> >Apache on Win98. How do i do ? Can someone help me? >> >thank you in advance >> >> -- >> PHP Windows Mailing List (http://www.php.net/) >> To unsubscribe, e-mail: php-windows-unsubscribe@lists.php.net >> For additional commands, e-mail: php-windows-help@lists.php.net >> To contact the list administrators, e-mail: php-list-admin@lists.php.net